Belt guard: XL models
FASTENER | TORQUE VALUE | |
Belt guard screw: XL Models | 120-180 in·lbs | 13.6-20.4 Nm |
Shock absorber mounting bolt | 45-50 ft·lbs | 61-68 Nm |
Removal
1. See Figure 2-160. Remove right side lower shock absorber mount locknut (1).
Figure 2-160. Belt guard/debris deflector: XL models: 1. Locknut; 2. Mounting bolt; 3. Washer; 4. Belt guard; 5. Screw; 6. Washer; 7. Nut; 8. Debris deflector; 9. Screw with captive washer (3); 10. Rear fork
2. Pull shock absorber mounting bolt (2) out slightly until it clears mounting hole in belt guard (4).
3. Remove screw (5), washer (6) and nut (7) securing front of belt guard to rear fork (10).
Installation
1. See Figure 2-160. Slide belt guard (4) into place. Tab on front of belt guard mounts outboard of mounting bracket on rear fork.
2. Secure front of belt guard to rear fork (10) with screw (5), washer (6) and nut (7). Tighten to 120-180 in·lbs (13.620.4 Nm).
3. Push lower shock absorber bolt (2) through rear belt guard mounting hole. Thread locknut (1) on screw. Tighten to 45-50 ft·lbs (61-68 Nm).
Debris deflector: XL models
FASTENER | TORQUE VALUE | |
Debris deflector screw: XL Models | 36-60 in·lbs | 4.1-6.8 Nm |
Removal
1. See Figure 2-160. Loosen, but do not remove, three screws with captive washers (9) securing debris deflector (8) to underside of rear fork (10).
2. Slide debris deflector forward until keyway slots in deflector clear screw heads.
Installation
1. See Figure 2-160. Position debris deflector (8) in place on underside of rear fork (10).
2. Fit large end of keyway slots in deflector over screw heads and captive washers (9). Slide deflector rearward to lock screws in slots.
3. Tighten to 36-60 in·lbs (4.1-6.8 Nm).
Belt guard: XR 1200X
FASTENER | TORQUE VALUE | |
Belt guard screw: XR 1200X | 72-96 in·lbs | 8.1-10.8 Nm |
Removal
See Figure 2-161. Remove two screws with captive washers (2) securing belt guard to top of rear fork (5).
Figure 2-161. Belt guard/debris deflector: XR 1200X: 1. Belt guard; 2. Screw with captive washer (2); 3. Debris deflector; 4. Screw with captive washer (3) (front screw inboard of debris deflector); 5. Rear fork
Installation
1. See Figure 2-161. Slide belt guard (1) into place on top of rear fork (5).
2. Install two screws with captive washers (2).
3. Tighten to 72-96 in·lbs (8.1-10.8 Nm).
Debris deflector: XR 1200X
FASTENER | TORQUE VALUE | |
Debris deflector screw: XR 1200X | 72-96 in·lbs | 8.1-10.8 Nm |
Removal
Note. Front screw is located inboard of debris deflector.
See Figure 2-161. Remove three screws with captive washers (4) securing debris deflector (3) to underside of rear fork (5).
Installation
1. See Figure 2-161. Position debris deflector (3) in place on underside of rear fork (5).
2. Install three screws (4).
3. Tighten to 72-96 in·lbs (8.1-10.8 Nm).