Electrical equipment and instruments of motorcycle BMW F650GS (2000-2007)

Wiring harness of motorcycle
View from left View from right General electrical equipment Circuit voltageV12 BatteryA/h12

Component positions in electronic equipment box
Relay positions in electronic equipment box: 1. Relief relay 2. BMS relay 3. Diode relay 4. Flasher unit Connectors, electronic equipment box: 5. Ignition light switch 6. Brake light switch 7. Multi-function switch, right 8. Multi-function switch,...

Removing and installing battery
Warning! Battery acid is highly caustic. Protect your eyes, face, hands, clothing and the paintwork. Remove left, right and centre covers. See Group 46. Caution! Disconnect the battery only with the ignition switched off. Disconnect the negative...

Removing and installing battery carrier
Place motorcycle on its centre stand. Remove seat. Remove left, right and centre covers. Remove the battery. See above. Remove the intake air pipe. See Group 13. Remove intake air silencer. See Group 13. Remove the starter relay from the holder....

Replacing fuses
Motorcycle fuses Remove seat. Open the cover of the fuse box. Replace the defective fuse. Fuses 1. BMS Compact — 20 A 2. Headlight, brake light, turn indicators, horn — 15A 3. Fan — 7.5 A 4. Heated handlebar grips — 7.5 A

Removing and installing electronic equipment box
Remove battery carrier. See above. Disconnect the expansion tank from the radiator, pull it to one side and allow it to dangle from the hose. Remove the fasteners securing the oil tank and allow the oil tank to dangle to one side on the hoses....

Removing and installing side stand switch
Place motorcycle on its centre stand. Remove the engine guard. Disconnect side-stand switch plug (1) and unclip the plug. Disconnect plug of oxygen sensor. Remove lower section. Cut the cable ties at the lower section (arrows). Remove retaining ring...

Removing and installing rear-brake switch for brake light
Remove seat. Remove right cover. Remove brake-light switch (4). Cut through the cable tie at the frame. Remove the fuse box. Remove the fastener securing the plug of the brake-light switch (arrow) at the frame Disconnect plug of brake light switch....

Removing and installing front-brake switch for brake light
Place motorcycle on its centre stand. Remove seat. Remove left, right and centre covers. Remove brake-light switch (1). Cut through cable clip. Disconnect the expansion tank and pull it to one side. Remove the fasteners securing the oil tank and...

Removing and installing horn
Remove front mudguard. See Group 46. Disconnect plug for horn (2). Remove fastener securing horn (1). Installation is the reverse of the removal procedure. Tightening torques: Horn to bottom fork bridge: 18 Nm Lid of electronic equipment box: 4 Nm...

Removing and installing idle-indicator switch
Remove cover for chain drive sprocket. Remove fastener securing cable to idle-indicator switch. Remove idle switch (3). Installation is the reverse of the removal procedure: pay particular attention to the following. Clean the threads of the...

Telltale/warning lights
Technical data Instruments Speedometer and revolution counter lightingW5/1.2 - 12V 1.2W Telltale and warning lights Flashing turn indicatorW5/1.2 - 12V 1.2W IdleW5/1.2 - 12V 1.2W Oil pressureW5/1.2 - 12V 1.2W Water temperatureW5/1.2 - 12V 1.2W High...

Removing and installing instrument panel
Place motorcycle on its centre stand. Remove left and right covers. Note: Note washers and rubber ring. Remove the windshield. Remove the instrument cover. Remove the fairing upper section. Disconnect the multi-pin plug from the headlight. Pull off...

Replacing telltale/warning lights
Remove instrument panel. Remove rubber grommet (3). Pull the indicator light out of the socket. Installation is the reverse of the removal procedure.

Disassembling and assembling instrument cluster
Remove instrument panel. Remove 3 securing screws from the transparent instrument cover and remove the cover. Remove the bezel. Remove the securing screws (arrows) and remove the cover (4). Remove the 3 securing screws (1) from the rear of the...

Removing and installing wiring harness
Remove instrument panel. See above. Pull out the warning lights (2) with the rubber grommet. Disconnect the wiring harness (3). Installation is the reverse of the removal procedure.