Exhaust system of motorcycle Harley Street 750 (2014-2021)
- Main
- Harley
- Street
- 750/500
- Engine and systems
- Exhaust system
See this section in russian language
Removing and installing muffler
Remove End Cap 1. See Figure 6-21. Remove end cap a. Remove screws (8). b. Remove end cap (1). Muffler 1. See Figure 6-21. Remove muffler. a. Discard clamp (6). b. Remove locknuts (4) and washers (3). c. Remove muffler (7). d. Remove screws (2)....
Remove End Cap 1. See Figure 6-21. Remove end cap a. Remove screws (8). b. Remove end cap (1). Muffler 1. See Figure 6-21. Remove muffler. a. Discard clamp (6). b. Remove locknuts (4) and washers (3). c. Remove muffler (7). d. Remove screws (2)....
Exhaust system
Prepare 1. Remove main fuse. See Power disconnect. 2. Disconnect 02 sensor connectors. See Oxygen (O2) sensor. Remove 1. See Figure 6-22. Remove exhaust system. a. Remove nuts (7). b. Remove locknuts (4) and washers (3). c. Remove exhaust system. 2....
Prepare 1. Remove main fuse. See Power disconnect. 2. Disconnect 02 sensor connectors. See Oxygen (O2) sensor. Remove 1. See Figure 6-22. Remove exhaust system. a. Remove nuts (7). b. Remove locknuts (4) and washers (3). c. Remove exhaust system. 2....
Intake leak test
Leak tester PART NUMBERTOOL NAME HD-41417PROPANE ENRICHMENT KIT Warning: Do not allow open flame or sparks near propane. Propane is extremely flammable, which could cause death or serious injury. Warning: Read and follow warnings and directions on...
Leak tester PART NUMBERTOOL NAME HD-41417PROPANE ENRICHMENT KIT Warning: Do not allow open flame or sparks near propane. Propane is extremely flammable, which could cause death or serious injury. Warning: Read and follow warnings and directions on...
Purge solenoid: California emissions
Prepare 1. Remove right side cover. Remove 1. Figure 6-24. Remove purge solenoid. a. Disconnect purge solenoid connector (2). b. Detach solenoid-to-induction module and canister-to-solenoid lines (3, 4). c. Pull back slightly on tab (5). Remove...
Prepare 1. Remove right side cover. Remove 1. Figure 6-24. Remove purge solenoid. a. Disconnect purge solenoid connector (2). b. Detach solenoid-to-induction module and canister-to-solenoid lines (3, 4). c. Pull back slightly on tab (5). Remove...
Charcoal canister: California emissions
Prepare 1. Remove lower belt guard. See Belt guards. Remove 1. See Figure 6-25. Remove charcoal canister and bracket. a. Detach hoses (1, 2) from charcoal canister. b. Remove nut (5) and washer. c. Remove screw (7) and bracket (4). 2. Separate...
Prepare 1. Remove lower belt guard. See Belt guards. Remove 1. See Figure 6-25. Remove charcoal canister and bracket. a. Detach hoses (1, 2) from charcoal canister. b. Remove nut (5) and washer. c. Remove screw (7) and bracket (4). 2. Separate...
Purge lines: California emissions
Prepare 1. Remove right side cover. See Side covers. Note: Lifting rear of fuel tank is only necessary for replacing purge solenoid to induction module line. 2. Lift rear of fuel tank if necessary. See Lift rear of fuel tank. Remove 1. See Figure...
Prepare 1. Remove right side cover. See Side covers. Note: Lifting rear of fuel tank is only necessary for replacing purge solenoid to induction module line. 2. Lift rear of fuel tank if necessary. See Lift rear of fuel tank. Remove 1. See Figure...
- Information for owner
- Introduction to manual
- Maintenance
- Engine and systems
- Engine repair
- Fuel system
- Cooling system
- Exhaust system
- Transmission
- Running gear and frame
- Frame and hinged elements
- Suspension and handlebar
- Brake system
- Wheels and tires
- Electric equipment
- Equipment and devices
- Starting and charging system
- Lighting and lamps