Note: All models have some rubber collars with captive threaded inserts that the screws thread into that fit into the panels at various places. Where the collar fits through both the panels it joins, it has to be removed before the panels can be separated Where the head of the collar sits between the two panels it joins, and therefore only actually passes through the lower of the two, it can remain in place. Take care not to lose them, and remove them for safekeeping if necessary. Check the rubber for damage, deformation and deterioration and replace the collars with new ones if necessary. Do not overtighten the screws or the collars could be damaged.
Cockpit trim panel(s)
1. On H and J (1987 and 1988) models, there is a panel on each side, each secured by three screws. Undo the screws and remove the panel, noting how it fits.
2. On К to X (1989 to 1999) models, there Is a single panel surrounding the instrument cluster secured by four screws. Undo the screws and remove the panel, noting how its tabs locate in the fairing side panels (see illustration).
![](https://motoinstruction.ru/img/honda/19/125912.jpg)
4.2. Undo the four screws and remove the panel
3. Installation is the reverse of removal.
Fairing side panels
4. Undo the three screws securing the panel (see illustration). Carefully draw the panel off the tank to release the pegs from the grommets, then release it from the cockpit trim panel and lift it to release the lower grommet from the peg on the bracket at the bottom (see illustrations).
![](https://motoinstruction.ru/img/honda/19/125913.jpg)
4.4a. Undo the screws (arrowed)...
![](https://motoinstruction.ru/img/honda/19/125914.jpg)
4.4b ...then release the pegs from the grommets (arrowed)
![](https://motoinstruction.ru/img/honda/19/125915.jpg)
4.4c. Utt the panel off the peg (arrowed)...
5. Either disconnect the turn signal wiring connector as It becomes accessible, or release the bulbholder from the turn signal by twisting it anti-clockwise (see illustration).
![](https://motoinstruction.ru/img/honda/19/125916.jpg)
4.5 ...and remove the bulbholder or disconnect the connector
6. Installation Is the reverse of removal.
Fairing
7. Remove the cockpit trim panel(s) (see above).
8. Undo the two screws securing the fairing on each side to the fairing side panels (see illustration 4.4a).
9. Support the fairing, then unscrew the four bolts securing it to the bracket (see illustration).
![](https://motoinstruction.ru/img/honda/19/125917.jpg)
4.9. Unscrew the two bolts (arrowed) on each side
10. Draw the fairing forward, noting how the pegs locate in the bracket, and disconnect the headlight and sidelight wiring connectors as they become accessible (see illustrations).
![](https://motoinstruction.ru/img/honda/19/125918.jpg)
4.10a. Draw the fairing forward...
![](https://motoinstruction.ru/img/honda/19/125919.jpg)
4.10b ...noting how the peg (A) locates in the bracket (B)...
![](https://motoinstruction.ru/img/honda/19/125920.jpg)
4.10c ...and disconnect the headlight wiring connector...
![](https://motoinstruction.ru/img/honda/19/125921.jpg)
4.10d ...and the sidelight wiring connector
11. Installation is the reverse of removal.
Windshield
12. Undo the screws securing the windshield to the fairing and remove the rubber collars, then carefully remove the windshield, noting how it fits (see illustration).
![](https://motoinstruction.ru/img/honda/19/125922.jpg)
4.12. Windshield screws (arrowed)
13. Installation is the reverse of removal.
Side panels
14. Unscrew the single bolt on the bottom of the panel, then carefully draw the panel away to release the pegs from the grommets (see illustrations).
![](https://motoinstruction.ru/img/honda/19/125923.jpg)
4.14a. Unscrew the bolt...
![](https://motoinstruction.ru/img/honda/19/125924.jpg)
4.14b ...and release the pegs from the grommets (arrowed)
15. Installation is the reverse of removal.
Belly pan
16. Undo the three screws and the two bolts and remove the belly pan (see illustration).
![](https://motoinstruction.ru/img/honda/19/125925.jpg)
4.16. Removing the belly pan
17. Installation is the reverse of removal. Replace the rubbers with new ones if they are damaged, deformed or deteriorated. Make sure the collars are fitted in the rubbers.
Stone guard
18. Unscrew the bolt securing the clutch cable holder to the clutch cover, then detach the cable end from the release arm, noting how it fits (see illustrations). Draw the cable out of the guard, noting its routing.
![](https://motoinstruction.ru/img/honda/19/125926.jpg)
4.18a. Unscrew the cable holder bolt...
![](https://motoinstruction.ru/img/honda/19/125927.jpg)
4.18b ...and release the cable end from the arm
19. Unscrew the two bolts in the middle, then lift the guard to release the tab on the bottom from the hook on the frame (see illustration).
![](https://motoinstruction.ru/img/honda/19/125928.jpg)
4.19. Unscrew the bolts (A) and release the tab (B)
20. Installation is the reverse of removal.