Frame and attachments of motorcycle Aprilia Shiver 750 (2007-2016)

Removing the tail pipe
Loosen the clamp between the exhaust end and the manifold. Undo and remove the upper screw. Protect the swingarm so as not to spoil it while removing the exhaust end. Keeping the plastic cover up, undo and remove the two central screws and collect...

Removing the manifold — tail pipe
Remove the front exhaust manifold. Remove the lambda probe. Loosen the clamp of the rear exhaust manifold. Remove the manifold - terminal coupling. See also specifications for this operation.

Removing the exhaust manifold
The engine and the exhaust system components get very hot and remain in this condition for a certain time interval after the engine has been switched off. Before handling these components, make sure that you are wearing insulating gloves or wait...

Removing the lambda sensor
Disconnect the lambda probe connector. Unscrew and remove the lambda probe. See also specifications for this operation.

Seat — removal and installation
Saddle removal Rest the vehicle on its stand. Insert the key (1) in the lock. Turn the key (1) anticlockwise Paying attention to the belt position, release and lift the saddle (2). Saddle lock Insert the bottom front lugs under the rear frame pin....

Headlight assy — removal and installation
pos.DescriptionTypeQuantityTorqueNotes 1TBEI screw fixing headlight bracket to steering baseM6x15210 Nm (7.37 lbf·ft)- 2Fastener for front turn indicatorsM523 Nm (2.21 lbf·ft)- 3Headlamp self-locking nutM6310 Nm (7.37 lbf·ft)- Remove the instrument...

Taillight assy — removal and installation
pos.DescriptionTypeQuantityTorqueNotes 1Upper TBEI screw fastening taillightM5x1624 Nm (2.95 lbf·ft)- 2Fastener for rear turn indicatorsM623 Nm (2.21 lbf·ft)- 3Reflector fastenerM522 Nm (1.47 lbf·ft)- 4Fastener for license plate lightM515 Nm (3.69...

Side body panels
The following operations refer to one side of the vehicle, but apply to both. Side fairings Undo and remove the two screws. Remove the cover. Undo and remove the screw. Remove the side fairing. Lower side fairings Remove the side fairing and...

License plate holder
Remove the saddle. Remove the helmet compartment. Undo and remove the screw. Unscrew and remove the two screws. Remove the clamp. Undo and remove the two screws; collect the spacers and the collars. Slide off the license plate holder towards the...

Air box — removal and installation
pos.DescriptionTypeQuantityTorqueNotes 1Cross head self-tapping screw fastening separator / filter boxM5x20103 Nm (2.21 lbf·ft)- 2SWP self-tapping screwM2.9x12 TCCR23 Nm (2.21 lbf·ft)- 3Cross head self-tapping screw fastening cover / filter...

Fuel tank — removal and installation
Remove the saddle. Remove the side fairings. Working from both sides, undo and remove the screw. Remove at least one side air duct. Slide off the ignition switch assembly panel. Undo and remove the two screws and collect the two collars. Undo and...

Front mudguard — removal and installation
Working from both sides, unscrew and remove the two screws. Remove the front mudguard. See also specifications for this operation.

Instrument cluster support
Undo and remove the two front screws. Working on both sides, loosen the nut and the screw and remove them. Working from both sides, tilting the front headlamp forward, undo and remove the screw and collect the nut. Working on the back of the...

Tail guard — removal and installation
Working from both sides of the vehicle, undo and remove the screw and remove the lateral air intake. Operating from both sides of the vehicle, undo and remove the two screws. Operating from both sides of the vehicle, undo and remove the screw. Undo...