How to use this manual 1. This manual is divided into sections. 2. The names of the sections are listed in the list of sections. 3. If you hold the manual as shown in the picture on the right, you can easily find the first page of any section. 4. The table of contents on...
Symbols for instructions and other information Symbols for USA The symbols below indicate instructions and other information required for servicing. Each symbol is associated with corresponding instructions. SYMBOL DESCRIPTION SYMBOL DESCRIPTION Torque control is required. The tightening torque...
Precautions and Notes Read this manual and follow the instructions strictly. The words BEWARE, CAUTION and NOTE are used to attract attention. Pay special attention to the text containing these words. Warning! Indicates a possible hazard that could result in death or...
General precautions Warning! Proper repair and maintenance procedures are important for the safety of the mechanic and for the safety and reliability of the motorcycle. When two or more people work together, ensure mutual safety. If it becomes necessary to start the...
Motorcycle appearance SUZUKI DR-Z250K1 (MODEL -2001) The appearance of the motorcycle may differ from that shown in the illustration depending on the market.
Serial number location Frame serial number or VIN (Vehicle Identification Number) pos.1 – stamped on the right side of the steering column. The engine serial number, position 2, is located on the left side of the engine crankcase. These numbers are used to register...
Fuel recommendations Fuel (for the US and Canadian markets) Use only unleaded gasoline with an anti-knock number of at least 90 (R+M) /2. Gasoline containing MTBE (Tetromethylbutyl ether), with less than 10% ethanol, or less than 5% methanol with appropriate solvents...
Motor oil and other fluids Engine oil (for the US market) SUZUKI recommends using SUZUKI PERFORMANCE 4 MOTOR OIL or SF - SG oil according to API classification (American Petroleum Institute). Recommended viscosity SAE 10W/40. If SAE 10W/40 viscosity is not available, please...
Motorcycle break-in procedure The manufacturer uses only the best materials and parts are processed to a high degree of cleanliness, however, a break-in procedure is necessary before using the motorcycle at maximum power. Further operation of the motorcycle will depend on how...
Information signs No. _ _ _ TAG OR PLATE (Name) Modification E-03 E-33 E-28 1 Noise level O O 2 Information plate O 3 Accreditation in Canada O 4 Fuel type O O O 5 Note in the manual O O 6 Caution decal (F) O 7 Caution decal (R) O O O 8 Compliance plate O 9...
Special tools and accessories 09900-00401. Set of L-shaped hex keys 09900-00410. Hex socket set (bit) 09900-06107. Circlip pliers 09900-06108. Circlip pliers 09900-09004. Core set 09900-20102. Calipers 09900-20202. Micrometer (25-50 mm) 09900-20204. Micrometer (75-100 mm)...
Tightening torque Engine Name N-m (Nm) kgf-m (kgs-m) lb-ft (lbf/ft) Cylinder head cover bolt 14 1.4 10 Cylinder head bolt [M:10] [M:6] 42 4.2 30.5 Cylinder head bolt [M:10] 10 1.0 7 Cylinder block base nut 10 1.0 7 Spark plug 11 1.1 8 Timing chain tensioner bolt 10...
Break-in procedure for the DR-Z250K1 motorcycle (E-24) Only the best available materials are used in the manufacturing process and all machined parts are manufactured to the highest standards. However, before subjecting the engine to maximum loads, it is necessary to run-in the moving parts. Future...
Motorcycle dashboard DR-Z250K1 (E-24) 1. Turn signal indicator; 2. Neutral indicator; 3. High beam indicator; 4. Mileage A; 5. Speedometer; 6. Clock/stopwatch/timer; 7. Mileage B/Odometer; 8. ADJUST – Button «Settings»; 9. SET TIME/TRIP 10. SET TRIP 11. MODE TIME 12. MODE TRIP Initial...