Electrical equipment and instruments of motorcycle Ducati Monster 696 (2007-2014)

Wiring diagram of motorcycle
Key to wiring diagram 1. Right-hand handlebar switch 2. Key switch 3. Horizontal cylinder spark plug 4. Vertical cylinder spark plug 5. Starter motor 6. Starter contactor 7. Battery 8. Main fuse 9. Regulator 10. Alternator 11. Rear right turn...

Key to fusebox
Position Item Rating 1 Key ON 10 A 2 Side lights, high/low beam 15 A 3 Consumers 15 A 4 Instrument panel 5 A 5 Injection 20 A 6 ECU 5 A 7 Spare 20 A 8 Spare 5 A

Routing of wiring on frame
The routing of the wiring has been optimised to ensure the minimum obstruction. Each section is designed to prevent interference with parts that might damage wires or cause operating failures when riding. The plates on the following pages show the...

Renewal of the headlight
Undo the screws (2) and remove the instrument panel shroud (1). Disconnect the instrument panel connector (A) from the main wiring harness (see plates in the chapter " Routing of wiring on frame "). Disconnect theheadlight wiring connector (B) and...

Changing bulbs
Changing the headlight bulbs Before replacing a burnt out light bulb, ensure that the replacement bulb has the same voltage and power rating as specified for the lighting device in question ( Lights/instrument panel ). Warning! The halogen light...

High beam headlights relay
Located alongside the battery and fixed to the battery support. To gain access to the relay, first remove the fuel tank ( Removal of the fuel tank ). The high beam relay (1) has been added to the electrical circuit to enable the lights power down...

Headlight aim
The motorcycle must be perfectly upright with the tires inflated to the correct pressure and with a rider seated, perfectly perpendicular to the longitudinal axis. Position the motorcycle 10 metres from a wall or a screen. On the wall or surface,...

Checking the indicating devices
In the event of a fault, the internal connections of the device must be checked in all operating conditions. To do this, disconnect the switch connector from the main wiring harness ( Routing of wiring on frame ). Test the device using either an...

Changing light bulbs
Changing the turn signal light bulbs Undo the screw (1) and detach the lens (2) from the turn signal support (3). The bulb has a bayonet-type end fitting: to remove it, push it in and turn it counter-clockwise. To remove the support (3), for the...

Checking protection and safety device components
Checking the key switch Disconnect the key switch (A) from the electrical system by opening its connection (see Routing of wiring on frame ) and use a multimeter to check its internal connections as follows: turn the key to OFF and connect a...

Checking the fuses
The main fuse box (1) is located on the right-hand side of the frame. The fuses are accessed by removing the cover, which shows the ampere ratings and mounting locations. For ampere ratings, refer to the " Routing of wiring on frame ". Caution!...

Instrument panel
Undo the screws (2) and remove the instrument panel shroud (1). Disconnect the wiring from the instrument panel (3). Undo the screws (4) and remove the instrument panel (3) from the front lights assembly support. When refitting, tighten the screws...

Instrument panel system
The instrument panel comprises a LCD digital display unit. The information on the display can be accessed using a 2-position rocker switch (1) and the headlight flasher button (2) on the left-hand handlebar switch. Underneath the digital display...

Display settings and functions
On switching on the power (key turned from OFF to ON), the instrument panel activates all the digits of the LCD for 1 second and switches on all the warning lights in sequence. It then reverts to "normal" mode and, in place of the odometer, shows...

Immobilizer and transponder
The immobilizer allows the vehicle to be started only if the rider uses the special ignition key which sends the identification code to a decoder housed in the instrument panel. The transmission-receiving system is composed of a TRANSPONDER housed...

Using a multimeter to check the electrical systems
Introduction This instrument allows you to measure resistances, voltages, and current values. Multimeters can be divided into two basic types: those with an analogue display and those with a digital display Units of the first type are equipped with...