Instruments and controls of motorcycle Ducati Monster 696 (2007-2014)

Load quantity information
The total weight of the motorcycle, including rider, passenger, cargo and accessories, must not exceed 390 kg. Place your luggage or heavy accessories as low as possible and close to the center of the motorcycle. Secure luggage according to the...

Identification data
There are two identification numbers on a Ducati motorcycle: one on the frame (pic. 1) and another one on the engine (pic. 2). Note. These numbers also indicate the make/lot of the motorcycle and are requested for the provision of spare parts.

Location of controls
1) Front brake lever. 2) Rotating accelerator handle («gas»). 3) Switch block (right hand). 4) Rear brake pedal. 5) Gear shift pedal. 6) Ignition and steering lock switch/lock. 7) Switch block (left hand). 8) Clutch lever. 9) Dashboard.

Dashboard
Pic. 4. 1) Liquid crystal display (more details) 2) NEUTRAL INDICATOR (N, green). Lights up when the gearbox is in neutral. 3) TURN SIGNAL INDICATOR (green). Flashes when the turn signals are on. 4) SELF-DIAGNOSTIC INDICATOR (orange), (on-board...

LCD display, main modes
Attention! Any adjustments to the instrument panel should only be made with the motorcycle secured. Never operate the dashboard controls while driving. The display mode the panel is in is indicated by special inscriptions: 1) SPEEDOMETER (mph, km/h)...

LCD display: view/change parameters
Pic. 7. As soon as the ignition switch is moved from the «OFF» (turned off) to position «ON» (included), the instrument panel will display all items on the LCD display for one second, switching the indicator lights one by one. Pic. 8. The instrument...

Odometer (odometer)
After turning on the ignition, the system automatically enters the total mileage display mode. The data is saved permanently and cannot be reset under any circumstances. Upon reaching 99999 km (or 99999 miles) indication «99999» remains unchanged.

Speedometer (speed indicator)
This function activates the display of the current speed of the motorcycle in kilometers per hour (km/h), or miles per hour (mph), increased by 8%. The maximum speed that can be shown is 299 km/h (186 mph). Above these values, the indicator shows a...

Trip kilometers (TRIP)
In this mode, if you press the MODE switch (1, fig. 9) to position B «▼» for three seconds, the counter will reset. If the value reaches 999.9, the counter will automatically reset to «zero» and starts counting again.

Reserve fuel (TRIP FUEL)
An indicator showing how many kilometers or miles have been driven on reserve fuel. As soon as the lamp warning of the transition to the reserve fuel volume lights up, the mode «Reserve fuel» turns on automatically, as can be seen on the display. As...

Air temperature indicator
Shows the ambient temperature. Display limits: -39°C...+124°C. If the sensor fails (the temperature is outside the limit values, or the sensor is disconnected), a series of hyphens is displayed «---» and the warning lamp lights up - diagnostic...

Oil temperature
Shows the oil temperature in the engine crankcase. Displayed as a graphic element (pic. 15-17). Pic. 15. Pic. 16. Pic. 17. The indication looks like this: if the temperature is between -40°C and +80°C, it is displayed «State 2» (see fig. 15). if the...

Service indicator
Indicator () starts to be displayed if the service period is approaching. The service indicator is displayed at the following mileage intervals: after the first 1000 kilometers on the odometer. after reaching 12,000 kilometers, and every subsequent...

Battery voltage indicator
To display this mode, enter the menu and select the page «WATT». Battery voltage information is displayed as follows: if the voltage is between 12.1 and 14.9 volts, it is constantly shown in numbers on the display; If the battery voltage is between...

Setting the idle speed
To display this mode, enter the menu and select the page «RPM». In addition to the upper speed graph, a digital display of them will appear on the display (see fig. 21). Now you can adjust the idle speed more accurately. Pic. 21.

Setting the screen backlight
In order to adjust the backlight of the dashboard screen, go to the menu and select the page «LIGHT SET». On this page, hold the switch in position B «▼» within three seconds. Next, when you press the switch to position B «▼», pages are displayed...

Using the mode «CIRCLE»
To use this function, enter the menu and go to the page «LAP» («Circle»). Turn on the mode by holding the MODE switch after pressing (1, fig. 9) in position B «▼» within three seconds. Stopwatch control in mode «Circle» done using the high beam...

DDA data collection
This mode is used to enable the DDA function (Ducati Data Analyzer - «Ducati data analyzer»). In this case, the DDA module must be connected to the corresponding connector. To activate DDA, enter the menu and translate «DDA» in a state «ON»...

Time setting function
The time display type is twelve-hour. «AM» stands for «before noon», «RM» - «afternoon». Enter the menu and select a page «SET». If you now turn the MODE switch (1, Fig 9) to position B «▼» for three seconds, you will enter the current time setting...

Diagnostic messages on the dashboard
The electronics checks the serviceability of the system within 60 seconds immediately after turning off the ignition. This function makes it possible to display and identify motorcycle faults. This makes it possible to detect and replace faulty...

Headlight saving function
This feature helps reduce battery usage by automatically turning off the headlights (headlights). The function works in the following three cases. 1) If, after turning on the ignition (moving the ignition switch from position «OFF» to position...

Courteous backlight function
This function can be used even with the ignition switch removed from the lock. After turning off the ignition, the instrument panel remains active for another 60 seconds. To turn on the headlight, you need to move the MODE switch within these 60...

Immobilization system
As an additional anti-theft device, the motorcycle is equipped with an IMMOBILIZER - an electronic system that automatically blocks the engine after the ignition is turned off. The head of each ignition key contains an electronic device that...

Motorcycle keys
The owner receives a set of two keys with a plate «code» (1, fig. 29) immobilization system. Pic. 29. Both keys are black (IN) identical and intended for normal use. They can: switch the ignition switch (starting the engine, etc); open and close the...

Code card
Code card (pic. thirty) is an application for ignition keys. There is an electronic code written on it (A, fig. 31), which will be useful if the engine is blocked by the immobilization system and, as a result, does not start. Pic. thirty. Pic. 31....

Immobilizer lock reset procedure
To remove the blocking by the immobilizer, you need to perform this procedure. This is done as follows: select the page «CODE» (code) in the instrument panel menu. Note. This page will be available if the immobilizer has issued at least one «error»....

Duplicate ignition keys
If you require an additional key, contact a Ducati Service Center with all existing keys and the Code Card. The service center will program new keys and reprogram existing ones (non-reprogrammable keys will not work, and it will be impossible to...

Ignition switch and steering lock
The lock is located in front of the fuel tank. The key can be in the lock in four positions: A) : «ON», «ON» - operations with the engine and lighting devices are possible; IN) : «OFF», «OFF» - operations with the engine and lighting devices are...

Switch block (left hand)
1) Two-position headlight switch: position = low beam; position = high beam. 2) switch = three-position turn signal switch: center position = off; position = left direction indicators (flashing); position = right direction indicators (flashing). To...

Clutch lever
Clutch lever (1, Fig. 35) equipped with a rotary regulator (2, fig. 36), which can be used to change the distance between the lever and the steering handle. To adjust, turn the adjuster wheel (2, fig. 36) to one of four positions. Pic. 35. Pic. 36....

Cold start lever
Cold start lever (fuel enricher) Designed to facilitate starting a cold engine and to increase idle speed immediately after starting. Use the cold start lever when the engine is cold (one or maximum two rectangles are displayed on the oil...

Switch block (right hand)
Pic. 38. 1) Two position switch «engine: stop»: position = work; position = engine stop. Attention! The main purpose of the switch «engine: stop» - turning off the engine in case of urgent need. After stopping, immediately move the switch to the...

Accelerator handle
Rotary handle (1) opens the fuel system throttle valve. When free, the handle returns to its original position, corresponding to engine idle speed.

Front brake lever
Press the lever (2) to control the front brake. The force transmission system is hydraulic, dose the pressure on the lever carefully. The front brake lever is equipped with a rotary adjuster (3, fig. 40), which can be used to change the distance...

Rear brake pedal
Press the pedal from top to bottom with your toe (1) to control the rear brake. The force transmission system from the pedal to the caliper is hydraulic.

Gear shift pedal
The gear shift pedal, after being pressed, returns to the middle position on its own. Switching is done with the toe of the left foot in one of two directions. Press the pedal down to shift into first gear and also to downshift. When the gear is...

Adjusting the position of the brake pedal and gear shift pedal
The position of the pedals can be adjusted relative to the footpegs to suit the rider's needs. To adjust the position of the gear shift pedal, unscrew the lock nuts (2) And (3), keeping the rod from rotating (1). Note. Lock-nut (2) has a left-hand...

Motorcycle appearance
1) Seat lock. 2) Exhaust muffler/catalyst. 3) Side support. 4) Adjustable rear shock absorber. 5) Rear view mirrors. 6) Gas tank cap. 7) Helmet fastening pin (inside).

Gas tank cap
Opening Lift the tongue (1) and insert the key into the lock. Turn the key 1/4 turn clockwise (to position «open») to open. Lift the lid. Closing Close the lid with the key inserted into its lock and press on top. Turn the key counterclockwise to...

Seat lock and helmet holder
Opening Insert the key into the lock and turn it, pressing the seat on top to make the process easier. Pull the seat back to free it from the front hooks. The cable for securing the helmet is located in the rear compartment of the niche under the...

Side support
Before lowering the side support, make sure the ground is level and firm enough. Do not park on soft ground, gravel, asphalt softened by the sun, etc. This may cause the motorcycle to fall. Park on slopes with the rear wheel lower. To lower the side...

Rear shock absorber adjustments
The shock absorber has external adjustment elements that make it possible to adapt the suspension to different loads. Regulator (1), located on the left side of the shock absorber near where it mounts to the rear subframe, modifies the rebound...

Motorcycle technical data
Dimensions (mm) Weight Dry weight of the equipped motorcycle without fuel: 161 kg. Weight of fully loaded motorcycle: 390 kg. Attention! Failure to monitor the motorcycle's maximum load may result in poor handling and affect motorcycle performance....

Location and designation of fuses
The electrical system components contain eight fuses located in the fuse box. Only six of the eight are connected to the electrical system, the remaining two are spare. Refer to the table below to determine where the fuses are located to protect the...