![](https://motoinstruction.ru/img/honda/9/116196.jpg)
General
A contaminated brake disc or pad reduces stopping power. Discard contaminated pads and clean a contaminated disc with a high quality brake degreasing agent.
Raise the front wheel off the ground by supporting the frame securely.
Refer to section 15 for hydraulic brake service.
Refer to section 19 for light, meter and switch service.
Specification
ITEM | STANDARD | SERVICE LIMIT Unit: mm (in) | ||
Minimum tire tread depth | — | 1.5 (0.06) | ||
Cold tire pressure | Up to 90 kg (200 lb) load | 225 kPa (2.25 kgf/cm2, 33 psi) | — | |
Up to maximum weight capacity | 225 kPa (2.25 kgf/cm2, 33 psi) | — | ||
Axle runout | — | 0.2 (0.01) | ||
Wheel rim runout | Radial | — | 2.0 (0.08) | |
Axial | — | 2.0 (0.08) | ||
Wheel balance weight | — | 60 g (2.1 oz) max. | ||
Fork | Spring free length | Right | 329.7 (12.98) | 323.1 (12.72) |
Left | 329.7 (12.98) | 323.1 (12.72) | ||
Slider runout | — | 0.20 (0.008) | ||
Recommended fork fluid | Pro Honda Suspension Fluid SS-8 | — | ||
Fluid level | Right | 111 (4.4) | — | |
Left | 110 (4.3) | — | ||
Fluid capacity | Right | 686±2.5 cm3 (23.2±0.08 US oz, 24.1±0.09 Imp oz) | — | |
Left | 770±2.5 cm3 (26.0±0.08 US oz, 27.1±0.09 Imp oz) | — | ||
Steering head bearing pre-load | 0.8- 1.2 kgf (1.8-2.6 Ibf) | — |
Torque values
Handlebar upper holder bolt | 26 N·m (2.7 kgf·m, 20 lbf·ft) | |
Handlebar lower holder nut | 64 N·m (6.5 kgf·m, 47 lbf·ft) | U-nut. |
Front axle bolt | 90 N·m (9.2 kgf·m, 67 lbf·ft) | |
Front axle holder bolt | 22 N·m (2.2 kgf·m, 16 lbf·ft) | |
Front brake disc bolt | 20 N·m (2.0 kgf·m, 14 lbf·ft) | ALOC bolt: replace with a new one. |
Steering stem nut | 100 N·m (10.2 kgf·m, 74 lbf·ft) | |
Top adjusting nut A | 17 N·m (1.7 kgf·m, 12 lbf·ft) | |
Top adjusting nut В | — | |
Fork top bridge pinch bolt | 55 N·m (5.6 kgf·m, 41 lbf·ft) | |
Fork bottom bridge pinch bolt | 24 N·m (2.4 kgf·m, 17 lbf·ft) | |
Fork cap | 34 N·m (3.5 kgf·m, 25 lbf·ft) | |
Fork socket bolt | 20 N·m (2.0 kgf·m, 14 lbf·ft) | Apply locking agent to the threads. |
Fork cap lock nut | 20 N·m (2.0 kgf·m, 14 lbf·ft) | |
Inner fork bolt | 98 N·m (10.0 kgf·m, 72 lbf·ft) | |
Front caliper mounting bolt | 30 N·m (3.1 kgf·m, 22 lbf·ft) | ALOC bolt: replace with a new one. |
Tools
Attachment, 37 x 40 mm | 07746-0010200 |
Attachment, 42 x 47 mm | 07746-0010300 |
Attachment, 52 x 55 mm | 07746-0010400 |
Pilot, 20 mm | 07746-0040500 |
Pilot, 35 mm | 07746-0040800 |
Bearing remover head, 20mm | 07746-0050600 |
Driver | 07749-0010000 |
Steering stem socket | 07916-3710100 |
Bearing race remover | 07946-3710500 |
Steering stem driver | 07946-MB00000 |
Driver handle attachment | 07949-3710001 |
Bearing remover shaft | 07GGD-0010100 |
Fork seal driver, 45 mm | 07KMD-KZ30100 |
Lock nut wrench, 36 x 44 mm | 07VMA-MZ0010A |