Installing the front mudguard
- Release the fastener (2).
- Insert the bushes (3).
- Fit the front wheel mudguard.
- Screw in the fastener (2).
- Tighten the fasteners (1).
- Tighten the fastener (2).
Tightening torques:
- Front mudguard to slider tube bridge M6 — 9 Nm
- Front mudguard to sliding tube M6 — 9 Nm
Installing the mirrors
![](https://motoinstruction.ru/img/bmw/21/127010.jpg)
Note: The gap at the mirror can be evened out by means of washers on the front bolt (3).
A: 1mm (0.04 in) washer (1) is fitted as standard.
- Hold the mirror casing with one hand and install it by gently tapping/pressing with the other.
- Check that the gap around the mirror is uniform.
- If necessary, use washers (0.5mm/1mm (0.02 in/ 0.04 in) in separate pack of items) to adjust the gap.
![](https://motoinstruction.ru/img/bmw/21/127011.jpg)
Installing the footrests
Installing the rear left footrest plate
Note: The front fastener (1) (long pointed-top screw) on the left-hand footrest plate also serves as the anchorage point for the battery bracket.
- Release the front fastener (1).
- Install the footrest plate using three mounting bolts.
Tightening torque:
Footrest plate to frame — 21 Nm
Installing the rear right footrest and footrest plate
![](https://motoinstruction.ru/img/bmw/21/127012.jpg)
- Install the front right footrest with torsion spring (4) and pin (2) with Optimoly MP3.
- Install circlip (3).
- Install the rear right footrest plate using three mounting bolts.
Tightening torque:
Footrest plate to frame — 21 Nm
![](https://motoinstruction.ru/img/bmw/21/127013.jpg)
Installing the engine spoilers
- Install the socket (3) with nut in the left-hand engine spoiler.
- Install rubber clip-on nuts (1) at rear of each side spoiler.
- Install three clip-on nuts (6) in each side spoiler (5, 9).
- Position four clip-on nuts (7) in the centre engine spoiler (8).
- Install the left engine spoiler (5).
- Insert the connector (2) for the socket (3) into the left engine spoiler.
- Install the right engine spoiler (9).
- Install the centre engine spoiler (8) paying particular attention to the corner (see arrow).
Tightening torque:
Spoiler sections — 2 Nm
Installing the reverser control
- Install actuating control for reverser (4) in left spoiler; install the control in the drive position, in other words with projection at top.
- Install Torx screw (T 25) to secure actuating lever for reverser.
Tightening torque:
Actuating control for reverser — 6 Nm (+ Loctite 243)
Installing the skirts
- Position two plug-in nuts (12) on the skirt (10).
- Install the skirt to the skirt bracket.
- Tighten the three screws (11, 14).
- Install the skirt cover (13).
Tightening torques:
Fairing — 2 Nm
![](https://motoinstruction.ru/img/bmw/21/127014.jpg)
Installing the top case
- Fit the lock cylinder.
- Raise the seat.
- Remove the rear seat.
- Open the top case.
- Release the knurled screw (7).
Warning: Support the lid to prevent it falling closed.
- Support the cover (1).
- Detach the control cable from the underside of the case.
- Use a screwdriver to unclip the removable lining from the lock.
- Detach the Velcro strip (6) from the rear panel.
- Remove the lining.
- Use the four fasteners (3) to secure the top case in the required position.
Note: The backrest can be adjusted by shifting the top case to either the front or rear position. Adjust by swapping the anchorages for cover of rear carrier (5) and top case. Always use the long screws to secure the top case. Additional instructions for moving the backrest.
- Remove four screws (4) for cover of rear carrier (5).
- Move the four screws (4) for the rear carrier cover forwards.
- Use long fasteners to secure the top case in its new position.
![](https://motoinstruction.ru/img/bmw/21/127015.jpg)
- Clip the cables for the radio remote control and the loudspeaker into the holders (1).
- Insert the top case plug connectors for the radio remote control (3) and the loudspeaker (2).
- Insert the removable lining and snap into place.
- Fit the knurled screw with the control cable.
- Plug in the connector (4) for rear seat heating, if applicable.
- Install the rear seat.
Tightening torque:
- Top case to rear frame — 9 Nm
- Rear carrier to frame — 9 Nm
- Rear seat to frame — 9 Nm