Saree guard: XL 883R, XL 1200C/C ANV (India)
FASTENER | TORQUE VALUE | |
Strut cover fastener | 96-156 in·lbs | 10.9-17.6 Nm |
Turn signal stalk locknut | 96-156 in·lbs | 10.9-17.6 Nm |
Strut cover fastener | 96-156 in·lbs | 10.9-17.6 Nm |
Saree guard, left-front, passenger footrest support bracket fastener | 16-20 ft·lbs | 21.7-27.1 Nm |
Shock absorber mounting bolt | 45-50 ft·lbs | 61-68 Nm |
Right, left-rear
1. Remove the rear strut cover. See 2.33 REAR FENDER: ALL XL MODELS EXCEPT XL 883N, XL 1200X/V, XL 883R/L.
2. See Figure 2-215. Remove the saree guard (1).
![](https://motoinstruction.ru/img/harley/12/117832.jpg)
Figure 2-215. Right, left-rear saree guard: 1. Right saree guard; 2. Strut cover fastener (2); 3. Washer (2); 4. Strut cover fastener locknut (2); 5. Turn signal stalk locknut (2); 6. Clip nut (2)
3. Install the saree guard.
- a. Fit the saree guard to the fender strut.
- b. Thread the turn signal connector and wire harness through the notch in the saree guard and the hole in the fender.
- c. Install the strut cover.
- d. Verify the installation of the rear fastener clip nut (6).
- e. Install the front and rear strut cover fasteners (2) and washers (3).
- f. Install the front fastener locknut (4) and the turn signal stalk locknut (5).
4. Tighten the fasteners:
- a. Front strut cover fastenerto 96-156 in·lbs (10.9-17.6 Nm).
- b. Turn signal stalk locknut to 96-156 in·lbs (10.9-17.6 Nm).
- c. Rear strut cover fastener to 96-156 in·lbs (10.9-17.6 Nm).
5. Complete the strut cover installation. See 2.33 REAR FENDER: ALL XL MODELS EXCEPT XL 883N, XL 1200X/V, XL 883R/L.
Left-front
1. Remove the left passenger footrest. See 2.43 PASSENGER FOOTRESTS, XL Models.
2. Remove the left upper rear shock absorber fastener and washer. See 2.24 SHOCK ABSORBERS, Removal.
3. See Figure 2-216. Remove the saree guard (1).
- a. Remove the stud cover (2).
- b. Remove the screw (3), the two washers (4) and the flange nut (5).
![](https://motoinstruction.ru/img/harley/12/117833.jpg)
Figure 2-216. Left-front saree guard: 1. Left-front saree guard; 2. Shock stud cover; 3. Fastener; 4. Washer; 5. Flange nut
Note. Apply 2-3 drops of LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (blue) to the threads of the shock absorber fastener.
4. Install the saree guard.
- a. Fit the saree guard to the footrest bracket and the shock mount.
- b. Install the screw, washers and the flange nut.
- c. Install the shock stud cover.
- d. Install the shock absorber fastener and washer.
5. Tighten the passenger footrest support bracket fastener to 16-20 ft·lbs (21.7-27.1 Nm).
6. Tighten the shock absorber mounting bolt to 45-50 ft·lbs (61-68 Nm).
7. Install the passenger footrest. See 2.43 PASSENGER FOOTRESTS, XL Models.