MotoInstruction.ru
Mobile
version
Articles
& news
Site
map
Feed
back
Add to
bookmark
English Русский
Aprilia
BMW
Ducati
Harley
Honda
Kawasaki
Suzuki
Triumph
Yamaha
Triumph:
Rocket▾
Rocket III (2004-2018)
Street Triple▾
765 R/RS [4] (2017-2024)
Tiger▾
Tiger 800 (2010-2019)

Twist grip position sensor — removal (Triumph Street Triple 765 R/RS)

  • Main
  • Triumph
  • Street Triple
  • 765 R/RS [4]
  • Engine and systems
  • Fuel and control system
  • Twist grip position sensor — r…
0
Warning!
  • Make sure the motorcycle is stabilised and adequately supported.
  • A correctly supported motorcycle will help prevent it from falling.
  • An unstable motorcycle may fall, causing injury to the operator or damage to the motorcycle.


Perform the following operations:
  • Seat - removal
  • Battery - removal
  • Fuel tank - removal
  • Airbox - removal
  • Twist grip - removal

Note: Note the routing of the harnesses around the right hand side of the headstock for installation.


1. Remove the cable guide on the right hand side of the headstock. Discard the fixings.

2. Remove the rubber band from the cables on the right hand side of the headstock.

1. Fixings; 2. Cable guide; 3. Rubber band

1. Fixings; 2. Cable guide; 3. Rubber band


3. Detach the twist grip harness electrical connector from its bracket and disconnect from the main harness.

1. Twist grip connector; 2. Bracket

1. Twist grip connector; 2. Bracket



Note: Note the routing of the twist grip harness for installation.


4. Route the twist grip harness out of the frame to the twist grip.

Note: Note the orientation of the twist grip position sensor for installation.


5. Slide the twist grip position sensor off the handlebar.
See this article in russian language
This article has been reviewed: Kirill Prokofiev
◀ Previous
Triumph 765 R/RS 4: Fuel and control system
Next ▶

Twist grip — installation
Twist grip — removal
Immobiliser/TPMS control module — installation
Immobiliser/TPMS control module — removal
Twist grip position sensor — installation
Intake air temperature sensor — removal
Intake air temperature sensor — installation
MAP sensor — removal
Similar articles about motorcycles of other brands
Throttle grip position sensor — removal Aprilia SL 750 Shiver (2007-2016)
Throttle position sensor (TPS) setting Suzuki Boulevard M109R (2006-2025)
Removing the crankshaft position sensor Yamaha FZ1 Fazer (2006-2015)
Throttle sensor position — adjustment Kawasaki ZX6R/ZX600J (2000-2002)
Throttle position sensor: TP — removal and installation Harley-Davidson V-Rod (2002-2006)
Link to this article in different formats
Comments and feedback from visitors
No comments yet, you will be the first!
 


Add up two numbers: 22 + 36

       



 

 
765 R/RS 4 (2017-2024) 
  • Information for owner
  • Introduction to manual
  • Engine and systems
  • Engine repair
  • Fuel and control system
  • Lubrication system
  • Cooling system
  • Transmission
  • Running gear and frame
  • Frame and hinged elements
  • Front suspension and handlebar
  • Rear suspension
  • Brake system
  • Wheels and tires
  • Electric equipment
  • Equipment and devices
  • Starting and charging system
  • Electrical circuits
Aprilia BMW Ducati Harley Honda Kawasaki Suzuki Triumph Yamaha
MotoInstruction.ru © 2021–2026 | Sitemap | Articles | Contacts | | Add to bookmarks | Mobile version