Removal
1. Position motorcycle upright on a suitable lift.
2. See Figure 6-120. Unplug JSS harness connector [133] (1).
![](https://motoinstruction.ru/img/harley/12/118358.jpg)
Figure 6-120. JSS connector: 1. JSS connector [133]; 2. J-clip
3. Cut cable strap securing JSS harness to frame.
4. See Figure 6-121. Remove screw (1). Remove JSS (2) and harness.
![](https://motoinstruction.ru/img/harley/12/118359.jpg)
Figure 6-121. JSS: 1. Screw; 2. JSS
Installation
FASTENER | TORQUE VALUE | |
JSS screw | 96-120 in·lbs | 10.9-13.6 Nm |
1. Install JSS. Finger-tighten screw.
Note. See Figure 6-122. Align JSS (1) with mounting tab (2) on jiffy stand yoke (3). If sensor is not properly aligned with mounting tab when screw is tightened, sensor or mounting tab may be damaged.
![](https://motoinstruction.ru/img/harley/12/118360.jpg)
Figure 6-122. JSS mounting (top view): 1. JSS; 2. Mounting tab; 3. Yoke
2. See Figure 6-123. With JSS (1) aligned with mounting tab on jiffy stand bracket, tighten screw (2) to 96-120 in·lbs (10.9-13.6 Nm).
![](https://motoinstruction.ru/img/harley/12/118361.jpg)
Figure 6-123. JSS harness routing: 1. JSS; 2. Screw; 3. Cable strap; 4. Plug
Note. Do not route JSS harness through J-clip. Harness can chafe against J-clip.
3. Route JSS harness forward along frame under left side of engine.
4. Secure harness to outboard side of frame with new cable strap (3).
5. If necessary, replace plug (4).
6. Connect JSS harness connector housing [133A] to main harness connector housing [133B].
Warning! The jiffy stand locks when placed in the full forward (down) position with vehicle weight on it. If the jiffy stand is not in the full forward (down) position with vehicle weight on it, the vehicle can fall over which could result in death or serious injury.
Warning! Always park motorcycle on a level, firm surface. An unbalanced motorcycle can fall over, which could result in death or serious injury.
Warning! Be sure jiffy stand is fully retracted before riding. If jiffy stand is not fully retracted, it can contact the road surface causing a loss of vehicle control, which could result in death or serious injury.
7. Test JSS with jiffy stand down and up:
- a. Turn ignition key to IGNITION.
- b. Shift transmission into gear.
- c. Switch OFF/RUN switch to RUN.
- d. Disengage clutch.
- e. Jiffy Stand Down: Press the START button. Engine should not start. "Side stand" should scroll across the odometer display.
- f. Jiffy Stand Up: Press the START button. Engine should start and run. "Side stand" should clear from the odometer display.
Operation
Jiffy stand down: engine non-start
See Figure 6-124. The engine will not start if the rider presses the starter button with the transmission in gear and the jiffy stand down. The message "Side stand" (1) will scroll across the odometer display.
![](https://motoinstruction.ru/img/harley/12/118362.jpg)
Figure 6-124. Side stand display: 1. Odometer display; 2. Reset switch
Raising the jiffy stand (or putting the transmission in neutral) will permit the engine to run and clear the message.
Jiffy stand down: engine starts and stalls
When the jiffy stand is down, the engine starts and runs if the ECM receives a signal from the neutral switch indicating the transmission is in neutral or a signal from the clutch switch indicating the clutch is engaged. The engine will continue to run after disengaging the clutch and shifting into gear. However with the jiffy stand still down, the engine will stall as the clutch is engaged.
Jiffy stand drops
If the jiffy stand drops out of the retracted position at speeds greater than 10 mph (15 km/h):
- The engine will continue to run.
- The warning indicators will flash twice.
- "Side stand" will scroll across the odometer display.
- The message will remain until the jiffy stand is in the retracted position.
Press the reset switch (2) once while the engine is running to clear the "Side stand" message.