![](https://motoinstruction.ru/img/kawasaki/23/129291.jpg)
1. Radiator; 2. Reserver Tank; 3. Reserver Tank Hose; 4. Reserver Tank Overflow Hose; 5. Outlet Hose; 6. Water pump Cover; 7. Thermostat Housing; 8. Inlet Hose; 9. Through the overflow hose as shown; 10. Wrap the clamp in the overflow hose; 11. Viewed Upside; 12. Front; 13. Viewed Rear Side
![](https://motoinstruction.ru/img/kawasaki/23/129292.jpg)
1. Clamps; 2. Clamp (Insert the clamp in the bracket.); 3. Clamps (Insert the clamps in the frame.); 4. Clamps (Insert the clamps from air cleaner housing side.); 5. Clamp (Insert the clamp from opening part turn to the body side.); 6. Clamp (Through the ignition switch lead, left switch housing lead in the clamp.); 7. Clamp (Through the left switch housing lead,ignition switch lead, and air switching valve lead in the clamp.); 8. Through the air switching valve lead upper the left switch housing lead; 9. After left switch housing lead connector and ignition switch lead connector connecting, put the connectors in the water-proof cover; 10. Ignition Switch Lead Connector; 11. Left Switch Housing Lead Connector; 12. Ignition Switch Lead; 13. Left Switch Housing Lead
![](https://motoinstruction.ru/img/kawasaki/23/129293.jpg)
1. Seat Lock Cable; 2. Insert the joint connector between the frame pipe and rear fender; 3. Run the harness through the cutout of the rear fender and between the frame pipes; 4. Frame Ground; 5. Kawasaki Self-diagnosis System Connector (Insert the connector to the bracket.); 6. Clamp (Insert the clamp in the rear fender front.); 7. Band the main harness with the frame so that the band run between the frame bracket and frame pipe (Position the band so that the edge of the band faces outward of the motorcycle, and do not pinch it in the cowling and frame.); 8. Band (Clamp the main harness at the frame cross pipe rearward while raising the harness upward, and position the band so that the edge of the band faces inside of the motorcycle.)
![](https://motoinstruction.ru/img/kawasaki/23/129294.jpg)
1. Install the clamp together with the rear fender rear (Clamp the turn signal leads and license plate light lead.); 2. Run the turn signal leads and license plate light lead into the frame hook; 3. ECU Connectors; 4. Install the clamp together with the rear fender rear (Clamp the turn signal leads, license plate light lead, and tail/brake light lead.); 5. Tail/Brake Light Lead
![](https://motoinstruction.ru/img/kawasaki/23/129295.jpg)
1. To Vehicle-down Sensor, Rear Brake Light Switch and Crankshaft Sensor; 2. Battery Negative Lead Connector; 3. Fuel Pump Lead; 4. Fuel Level Sensor Lead; 5. Clamp the main harness, and insert it in the rear fender front; 6. Through the main harness to the rear fender front hook so that the main harness dose not through loosely between the hook and starter relay; 7. Fuel Pump Lead Connector; 8. Through the harness into the starter relay cover slit; 9. Fuel Level Sensor Lead Connector; 10. Battery Negative Cable; 11. Battery Positive Cable; 12. Main Harness; 13. Viewed Rear Side
![](https://motoinstruction.ru/img/kawasaki/23/129296.jpg)
1. Through the main harness to the rear fender front opening; 2. Clamp (Insert the clamp to the frame.); 3. Vehicle-down Sensor; 4. Rear Brake Hose (To Rear Master Cylinder); 5. Through the leads of the rear brake light switch and vehicle-down sensor from forward of the rear shock absorber mounting portion; 6. Rear Brake Light Switch Connector (After connected, push it forward to the frame cross pipe upper surface.); 7. Rear Brake Light Switch
![](https://motoinstruction.ru/img/kawasaki/23/129297.jpg)
1. Subthrottle Valve Actuator Lead; 2. Clamp (Push the subthrottle valve actuator lead under the clamp, and clamp the subthrottle sensor lead and subthrottle valve actuator lead to the delivery pipe.); 3. Clamp (clamp the harness.); 4. Subthrottle Sensor Lead; 5. Inlet Air Pressure Sensor; 6. Clamp (Through the main harness and radiator fan lead in the clamp, and insert the clamp in the frame.); 7. Through the horn lead between the radiator hose and frame; 8. Radiator Fan Lead Connector; 9. To Front Left Turn Signal Light; 10. Through the inlet air pressure sensor lead between the frame and front frame cover; 11. Clamp (Insert the clamp in the frame bracket.)
![](https://motoinstruction.ru/img/kawasaki/23/129298.jpg)
1. Clamp (Insert the clamp in the frame.); 2. Clamp (Insert the clamp in the horn bracket.); 3. Insert the horn lead terminal from the under; 4. Battery Negative Cable; 5. Battery Positive Cable; 6. Main Harness; 7. Starter Motor Cable
![](https://motoinstruction.ru/img/kawasaki/23/129299.jpg)
1. Fuel Tank Drain Hose (Through the drain hose between main harness and air cleaner housing.); 2. Air Cleaner Drain Hose; 3. Fuel Tank Drain Hose; 4. Clamp (Through the sidestand switch lead, oxygen sensor lead (europe models), and fuel tank drain hose in the clamp.); 5. Clamp (Through the sidestand switch lead and oxygen sensor lead (europe models.); 6. Clamp (Through the drain hose in the clamp.); 7. Oxygen Sensor Lead (Europe Models); 8. Sidestand Switch Lead; 9. Corrugated Tube; 10. From this side, through the fuel tank drain hose, corrugated tube and air cleaner drain hose between the chain guide and engine; 11. Corrugated Tube (Through the neutral switch lead, speed sensor lead, sidestand switch lead, and alternator switch lead in the tube, and face the slit of the tube inside.); 12. Speed Sensor; 13. Bracket; 14. Neutral Switch Lead
![](https://motoinstruction.ru/img/kawasaki/23/129300.jpg)
1. Headlight (low) connector with green tape on the headlight lead; 2. Clamp (Insert the clamp to the handle.); 3. Turn Signal Relay Lead; 4. Left City Light Connector; 5. Run the main harness between the clamp and pipe; 6. Headlight (high) Connector; 7. Band (Clamp the right city light lead with the oil pressure warning indicator light (LED) delay unit lead to the middle fairing bracket.); 8. Right City Light Connector; 9. Oil Pressure Warning Indicator Light (LED) Delay Unit Connector; 10. Insert the unit in the middle upper fairing bracket facing the unit lead inside; 11. Clutch Cable; 12. Left Switch Housing Lead (Through the left switch housing lead in the clamp.); 13. Clamp (From the on sequentially, through the ignition switch lead, left switch housing lead, and main harness.); 14. Main Harness; 15. Clamp (Clamp the brake hose in the clamp.); 16. Clamp (Insert the clamp in the middle fairing bracket.); 17. Through the ignition switch in the clamp as shown; 18. Through the clutch cable in the clamps; 19. Band (Clamp the main harness to the middle fairing bracket.)
![](https://motoinstruction.ru/img/kawasaki/23/129301.jpg)
1. Clamp (Insert the clamp to the handlebar.); 2. Through the brake hose, right switch housing lead, and throttle cables in the upper and lower clamps; 3. Right Switch Housing Lead; 4. Throttle Cable (Accelerator); 5. Throttle Cable (Decelerator); 6. Clamp (From the on sequentially, through the clutch cable and throttle cables.); 7. Clamp (Through the right switch housing lead in the clamp, and insert the clamp in the frame.); 8. Through the radiator hose to the space of the frame bracket; 9. Radiator Hose; 10. Front Right Turn Signal Light Lead; 11. From this side, through the turn signal light lead, reserver tank hose, and reserver tank overflow hose; 12. Clamp (Insert the clamp in the frame.); 13. Clamp (Through the clutch cable in the clamp.); 14. Clutch Cable
![](https://motoinstruction.ru/img/kawasaki/23/129302.jpg)
1. Seat Lock Cable; 2. Seat Lock; 3. Through the seat lock cable to the space of the frame bracket; 4. Install the hook faces downward.
![](https://motoinstruction.ru/img/kawasaki/23/129303.jpg)
1. Clamp; 2. Clamp; 3. Brake Hose; 4. Bracket; 5. Brake Hose
![](https://motoinstruction.ru/img/kawasaki/23/129304.jpg)
1. Clamp; 2. Clamp; 3. Brake Hose; 4. Face the paint mark outside; 5. Viewed A