First Step
- Turn on the ignition switch.
- The following lights should goon according to below table.
| City Lights [A] | goes on |
| Taillight [B] | goes on |
| License Plate Light [C] | goes on |
| Meter Panel Illumination Light (LED) [D] | goes on |
| Meter Panel LCD [E] | goes on |
| Neutral Indicator Light (LED) [F] | goes on |
| Oil Pressure Warning Indicator Light (LED) [G] | goes on |
| FI Indicator Light (LED) [H] | goes on (about 2 seconds) |
KLE650B Models
| ABS Indicator Light (LED) [I] | goes on |
If the light does not go on, inspect or replace the following item.
- Battery (See Charging Condition Inspection in the Electrical System chapter)
- Applicable Bulb (see Wiring Diagram in the Electrical System chapter)
- Meter Unit for Meter Panel LCD (see Meter Unit Inspection in the Electrical System chapter)
- Meter Unit for Neutral Indicator Light (LED) (see Meter Unit Inspection in the Electrical System chapter)
- Meter Unit for Oil Pressure Warning Indicator Light (LED) (see Meter Unit Inspection in the Electrical System chapter)
- Meter Unit for Illumination Light (LED) (see Meter Unit Inspection in the Electrical System chapter)
- Meter Unit for FI Indicator Light (LED) (see Meter Unit Inspection in the Electrical System chapter)
- Meter Unit for ABS Indicator Light (LED) (See ABS Indicator Light (LED) Inspection in the Brakes chapter) (KLE650B Models)
- ECU (See ECU Power Supply Inspection in the Fuel System (DFI) chapter)
- Main Fuse 30 A and Taillight Fuse 10 A (See Fuse Inspection in the Electrical System chapter)
- Ignition Switch (See Switch Inspection in the Electrical System chapter)
- Neutral Switch (See Switch Inspection in the Electrical System chapter)
- Harness (See Wiring Inspection in the Electrical System chapter)
- Turn off the ignition switch.
- The all lights should go off.
If the light does not go off, replace the ignition switch.
Second Step
- Turn the ignition switch to P (Park) position.
- The city light, taillight and license plate light should go on.
If the light does not go on, inspect or replace the following item.
Ignition Switch (See Switch Inspection in the Electrical System chapter).
Third Step
- Turn on the turn signal switch [A] (left or right position).
- The left or right turn signal lights [B] (front and rear) according to the switch position should flash.
- The turn signal indicator light (LED) [C] in the meter unit should flash.
If the each light does not flash, inspect or replace the following item.
- Turn Signal Light Bulb (See Turn Signal Light Bulb Replacement in the Electrical System chapter)
- Meter Unit for Turn Signal Light Indicator Light (LED) (see Meter Unit Inspection in the Electrical System chapter)
- Turn Signal Relay Fuse 10 A (See Fuse Inspection in the Electrical System chapter)
- Turn Signal Switch (See Switch Inspection in the Electrical System chapter)
- Turn Signal Relay (See Turn Signal Relay Inspection in the Electrical System chapter)
- Harness (See Wiring Inspection in the Electrical System chapter)
- Push the turn signal switch.
- The turn signal lights and indicator light (LED) should go off.
If the light does not go off, inspect or replace the following item.
- Turn Signal Switch (See Switch Inspection in the Electrical System chapter)
- Turn Signal Relay (See Turn Signal Relay Inspection in the Electrical System chapter)
Fourth Step
- Set the dimmer switch [A] to low beam position.
- Start the engine.
- The low beam headlight should go on.
If the low beam headlight does not go on, inspect or replace the following item.
- Headlight Low Beam Bulb (See Headlight Bulb Replacement in the Electrical System chapter)
- Headlight Fuse 10 A (See Fuse Inspection in the Electrical System chapter)
- Dimmer Switch (See Switch Inspection in the Electrical System chapter)
- Headlight Relay in Relay Box (See Relay Circuit Inspection in the Electrical System chapter)
- Harness (See Wiring Inspection in the Electrical System chapter)
- Set the dimmer switch to high beam position.
- The low beam [A] and high beam [B] headlights should go on.
- The high beam indicator light (LED) [C] should go on.
If the high beam headlight and/or high beam indicator light (LED) does not go on, inspect or replace the following item.
- Headlight High Beam Bulb (See Headlight Bulb Replacement in the Electrical System chapter)
- Dimmer Switch (See Switch Inspection in the Electrical System chapter)
- Turn off the engine stop switch.
- The low beam and high beam headlights should stay going on.
If the headlights and high beam indicator light (LED) does go off, inspect or replace the following item.
- Headlight Relay in Relay Box (See Relay Circuit Inspection in the Electrical System chapter)
- Turn off the ignition switch.
- The headlights and high beam indicator light (LED) should go off.
