Rear Seat — removal Removal The seat lock is located on the rear mudguard, below the rear light unit. To remove the seat, insert the ignition key into the seat lock and turn it anti-clockwise while pressing down on the rear of the seat. This will release the seat from...
Rider's Seat — removal Removal To remove the rider's seat, remove the rear seat (see page 16-13 ). Grasp the riders seat on either side, and slide it rearwards and upwards for complete removal from the motorcycle. To refit the seat, engage the seat's front rail into the...
Lower Radiator Panel — removal and installation Removal 1. Remove the two radiator infill fixings. 1. Radiator infill; 2. Fixings 2. Remove the fixing and remove the panel towards the rear of the motorcycle. 1. Lower radiator panel; 2. Fixing Installation 1. Align the panel the hook on the upper...
Upper Radiator Panel — removal and installation Removal 1. Remove the rider's seat (see page 16-13 ). 2. Disconnect the battery, negative (black lead first). 3. Remove the lower radiator panel (see page 16-14 ). 4. Remove and discard the radiator infill panel fixing. 1. Radiator infill panel; 2....
Radiator Infill Panel — removal and installation Removal 1. Remove the rider's seat (see page 16-13 ). 2. Disconnect the battery, negative (black) lead first. 3. Remove the lower radiator panel (see page 16-14 ). 4. Remove the upper radiator panel (see page 16-14 ). 5. Right hand radiator infill...
Beak — Tiger 800XC only Removal 1. Remove the four fixings and remove the beak in an upwards direction. 1. Beak; 2. Fixings Installation 1. Installation is the reverse of removal noting the following: Note: Tighten the fixings to 3 Nm.
Cockpit Assembly Removal Note: This procedure describes the removal and installation procedure for both Tiger 800 and Tiger 800XC models. 1. Remove the rider's seat (see page 16-13 ). 2. Disconnect the battery, negative (black) lead first. 3. Remove the two inner...
Fuel Tank Infill Panel — removal and installation Removal 1. Remove the rider's seat (see page 16-13 ). 2. Remove the rear fixing, located to the rear of the airbox. 1. Fuel tank infill panel; 2. Rear fixing (right hand shown); 3. Rear tang; 4. Front tang location 3. Lift the infill panel upwards,...
Removal and Installation Windscreen Removal 1. Release the two upper mounting fixings, collecting the nuts from the inside of the mounting as you do so. 2. Remove the two side fixings and remove the windscreen. 1. Upper fixing (left hand shown); 2. Side fixing (left hand shown)...
Front Mudguard — Tiger 800 Removal 1. Detach the front brake hose from the two clips on the front mudguard. 2. Remove the two right hand fixings and collect the front fork protector. 1. Brake hose clip; 2. Front fork protector; 3. Mudguard; 4. Fixings 3. Support the front...
Front Mudguard — Tiger 800XC Removal 1. Detach the front brake hose from the two clips on the front mudguard. 2. Remove and discard the two rear fixings. 3. Support the front mudguard and remove the four lower fixings. Discard the fixings. 4. Remove the mudguard towards the...
Rear Rack — removal and installation Removal 1. Remove the rear seat (see page 16-13 ). 2. Remove the four fixings and remove the rack. 1. Rear rack; 2. Fixings Installation 1. Position the rear rack to the motorcycle. 2. Refit the four fixings and tighten to 3 Nm. 3. Refit the rear...
Rear Side Panel — removal and installation Removal 1. Remove the rider's seat (see page 16-13 ). 2. Disconnect the battery, negative (black) lead first. 3. Remove the rear rack (see page 16-20 ). 4. Remove the rear grab handle bolt. 5. Remove the front nut and bolt and remove the grab...
Rear Mudguard — removal and installation Removal 1. Remove the rider's seat (see page 16-13 ). 2. Disconnect the battery, negative (black) lead first. 3. Remove the rear rack (see page 16-20 ). 4. Remove the rear side pa nels (see page 16-21 ). Note: The reflector bracket is secured by a...
Sump Guard — removal and installation Removal 1. Remove and discard the two front fixings. 2. Remove and discard the four nuts and remove the sump guard. 1. Sump guard; 2. Front fixings; 3. Rear fixing nuts Installation 1. Align the sump guard to the motorcycle and secure with four new...
Frame, Footrests and Fixings — inspection Inspection 1. Inspect the frame, footrests and bodywork for damage, cracks, chafing and other dangerous conditions. Check bodywork and frame fixings for security. Warning: If the motorcycle is involved in an accident or collision it must be taken to...