Fastener torque values in this chapter
The table below lists torque values for all fasteners presented in this chapter.
FASTENER | TORQUE VALUE | NOTES | |
Alternator rotor bolt | 160.0-170.0 Nm | 118-125 ft·lbs | Removing and installing alternator, Install |
Battery ground stud | 6.0-10.0 Nm | 54-88 in·lbs | Power disconnect, Connect Power |
Battery tray cover screws | 2.3-3.3 Nm | 21-29 in·lbs | Battery tray, Install |
Battery tray screws | 2.3-3.3 Nm | 21-29 in·lbs | Battery tray, Install |
Cooling fan screws | 2.3-3.3 Nm | 21-29 in·lbs | Removing and installing cooling fan, Install |
ECM screws | 2.3-3.3 Nm | 21-29 in·lbs | Electronic control module (ECM), Install |
Engine ground cable nut | 6.0-10.0 Nm | 54-88 in·lbs | Engine ground cable, Install |
Engine ground cable screw | 9.0-11.0 Nm | 80-97 in·lbs | Engine ground cable, Install |
Handlebar switch housing screws, left | 0.8-1.1 Nm | 7-9 in·lbs | Left handlebar switch housing, Install |
Headlamp horizontal adjustment locknut | 34.2-41.8 Nm | 26-30 ft·lbs | Removing and installing headlamp, Install |
Headlamp horizontal adjustment locknut | 34.2-41.8 Nm | 26-30 ft·lbs | Removing and installing headlamp, Adjust |
Headlamp vertical adjustment locknut | 20.6-25.5 Nm | 16-18 ft·lbs | Removing and installing headlamp, Install |
Headlamp vertical adjustment locknut | 20.6-25.5 Nm | 16-18 ft·lbs | Removing and installing headlamp, Adjust |
Horn bracket screws | 42.7-47.3 Nm | 32-34 ft·lbs | Removing and installing horn, Install |
Horn screws | 4.5-5.5 Nm | 40-48 in·lbs | Removing and installing horn, Install |
Ignition coil inner bracket screws | 22.5-27.5 Nm | 17-20 ft·lbs | Ignition coil, Install |
Ignition coil screws | 9.0-11.0 Nm | 80-97 in·lbs | Ignition coil, Install |
Ignition switch screws | 6.2-6.8 Nm | 55-60 in·lbs | Ignition switch, Install |
Jiffy stand sensor bracket screw | 22.0-29.0 Nm | 17-21 ft·lbs | Jiffy stand sensor, Install |
Jiffy stand sensor screw | 9.0-11.0 Nm | 80-97 in·lbs | Jiffy stand sensor, Install |
License plate lamp screws | 0.8-1.2 Nm | 7-11 in·lbs | License plate lamp, Install |
Mud guard screws | 2.3-3.3 Nm | 21-29 in·lbs | Electronic control module (ECM), Install |
Neutral switch screws | 5.0-7.0 Nm | 45-62 in·lbs | Neutral indicator switch, Install |
Oil pressure switch | 10.0-12.0 Nm | 89-106 in·lbs | Oil pressure switch, Install |
Rear lighting harness retainer screw | 1.2-2.0 Nm | 11-17 in·lbs | Rear turn signal lamps, Install |
Rear lighting harness retainer screw | 1.2-2.0 Nm | 11-17 in·lbs | License plate lamp, Install |
Speedometer screws | 10.8-13.2 Nm | 96-116 in·lbs | Removing and installing speedometer, Install |
Starter relay screws | 2.3-3.3 Nm | 21-29 in·lbs | Starter solenoid, Install |
Starter relay terminal locknuts | 6.0-10.0 Nm | 54-88 in·lbs | Starter solenoid, Install |
Starter screws | 10.0-12.0 Nm | 89-106 in·lbs | Removing and installing starter, Install |
Starter terminal nut | 6.0-10.0 Nm | 54-88 in·lbs | Removing and installing starter, Install |
Tail lamp screws | 3.9-5.9 Nm | 35-52 in·lbs | 8.22 TAIL LAMP, Install |
Turn signal housing screw, rear | 3.9-5.9 Nm | 35-52 in·lbs | Rear turn signal lamps, Install |
Turn signal housing screws, front | 9.0-11.0 Nm | 80-97 in·lbs | Front turn signal lamps, Install |
Turn signal lens screw | 0.6-0.8 Nm | 5-7 in·lbs | Front turn signal lamps, Install |
Turn signal lens screw | 0.6-0.8 Nm | 5-7 in·lbs | Rear turn signal lamps, Install |
Voltage regulator bracket screws | 22.5-27.5 Nm | 17-20 ft·lbs | Voltage regulator, Install |
Voltage regulator screws | 9.0-11.0 Nm | 80-97 in·lbs | Voltage regulator, Install |
VSS screw | 7.0-9.0 Nm | 62-79 in·lbs | Vehicle speed sensor (VSS), Install |